[PSUBS-MAILIST] G.L. summary Pressure Hull

[hank pronk]

Hi Brian,
Yes the bearing housing is completely full of oil, no compensation needed.  
Did you test your battery pods?
Hank



On Thursday, December 12, 2013 3:44:01 PM, brian <brian at ojaivalleybeefarm.com> wrote:
  
Is that so you don't have to compensate that area?

-----Original Message-----
From: "hank pronk" <hanker_20032000 at yahoo.ca>
Sent 12/12/2013 10:28:11 AM
To: "Personal Submersibles General Discussion" <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] G.L. summary Pressure Hull


Vance, 
I posted a picture of my new motor and seal assembly, (Gamma Restoration)  you can see I put  bearings and seals in the tail cone. You can't see it but I also have two ss lines that feed water to the shaft tube from outside the mbt.  This ensures the tube fills before I run the motor and also drains to prevent freezing. 
Hank 



On Thursday, December 12, 2013
10:31:05 AM, hank pronk <hanker_20032000 at yahoo.ca> wrote:
  
Dan, 
Thank you, I will play around with it.  I guess that's how we learn. 
Hank 



On Thursday, December 12, 2013 9:48:21 AM,
Dan H. <jumachine at comcast.net> wrote:
  
 
If you don't have a taper attachment, use the
compound slide on the lathe.  It's tricky to set since your working on
fractions of a degree for a good fit but you fine tune it with a few trial
pieces.   
  
Dan H. 
----- Original Message -----  
>From: hank
pronk  
>To: Personal Submersibles General
Discussion  
>Sent: Thursday, December 12, 2013 10:16
AM 
>Subject: Re: [PSUBS-MAILIST] G.L. summary
Pressure Hull 
>
> 
>Does anyone have a trick to machining an inside taper without lathe
 attachments.  I need to make a hub to fit a tapered
shaft.  I made one by trial and error and it will work but it is not
perfect.  
>Hank  
>
>
>
>On Thursday, December 12, 2013 7:13:39
AM, Jon Wallace <jonw at psubs.org>
wrote:
> 
>
>I should have stated up
front that we were just having some fun and I hope nobody concentrating on
ROV/AUV development and operation takes offense.  PSUBS welcomes ROV and
AUV discussions here as well.
>
>Jon
>
>
>
>On 12/11/2013 9:57 PM, Alan James wrote:
>  
>Thanks Keith, 
>>hope
didn't see the phone sex & ROV comments 
>>earlier  
>>Keith
owns a ROV company. 
>>Alan 
>> 
>   
>
>_______________________________________________
>Personal_Submersibles mailing list
>Personal_Submersibles at psubs.org
>http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
> 
>
>       
>
>________________________________
>
_______________________________________________
>Personal_Submersibles
mailing
list
>Personal_Submersibles at psubs.org
>http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>  

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
 

        

     
_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles 

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20131212/689a1e1e/attachment.html>