<DIV style="font-family:Arial, sans-serif; font-size:10pt;"><DIV>Rick, Wouldn't the electrical tape kind of defeat the purpose of running the threaded rod in the potted epoxy? If I'm understanding you right. I'll make sure I have enough space for possible heat problems , I'll have to look this over again . thanks all !</DIV><DIV> </DIV><DIV>Brian<BR><BR>--- personal_submersibles@psubs.org wrote:<BR><BR>From: Rick Patton via Personal_Submersibles <personal_submersibles@psubs.org><BR>To: Personal Submersibles General Discussion <personal_submersibles@psubs.org><BR>Subject: Re: [PSUBS-MAILIST] penetrator<BR>Date: Fri, 16 Dec 2016 15:56:10 -1000<BR><BR></DIV><DIV dir="ltr">Brian<DIV>I am using two each 1/8" copper rods on my Minn-Kotta's which I am guessing will equal the same as the 10 gauge wire they use and not knowing how resistant epoxy is to conducting current, I am going with an 1/8" separation and also wrapping both rods with electrical tape to be safe.</DIV><DIV><BR></DIV><DIV>Rick</DIV></DIV><DIV><BR><DIV>On Fri, Dec 16, 2016 at 3:46 PM, hank pronk via Personal_Submersibles <SPAN dir="ltr"><<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>></SPAN> wrote:<BR><BLOCKQUOTE style="margin: 0px 0px 0px 0.8ex; padding-left: 1ex; border-left-color: rgb(204, 204, 204); border-left-width: 1px; border-left-style: solid;"><DIV><DIV style="color: rgb(0, 0, 0); font-family: HelveticaNeue,Helvetica Neue,Helvetica,Arial,Lucida Grande,sans-serif; font-size: 12px; background-color: rgb(255, 255, 255);"><DIV><SPAN>Brian, </SPAN></DIV><DIV dir="ltr"><SPAN>I try to have as much separation as possible just to ensure they don't make contact, but 1\16 inch has worked fine for me. If you have 4 rods it will be crowded for putting wire connectors on. You can always bend the rods to make clearance also. </SPAN></DIV><DIV dir="ltr"><SPAN>Hank</SPAN></DIV><DIV><DIV> <DIV><BR><BR></DIV><DIV style="display: block;"> <DIV style="font-family: HelveticaNeue,Helvetica Neue,Helvetica,Arial,Lucida Grande,sans-serif; font-size: 12px;"> <DIV style="font-family: HelveticaNeue,Helvetica Neue,Helvetica,Arial,Lucida Grande,sans-serif; font-size: 16px;"> <DIV dir="ltr"><FONT face="Arial" size="2"> On Friday, December 16, 2016 5:49 PM, Brian Cox via Personal_Submersibles <<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>> wrote:<BR></FONT></DIV> <BR><BR> <DIV><DIV><DIV><DIV style="font-family: Arial,sans-serif; font-size: 10pt;"><DIV>Hank, Starting to work on my electrical penetrators for my motor pods . I need to run 4 - 1/4" copper threaded rods thru a penetrator what kind of separation between them is adequate ? or should I break it up into two penetrators?</DIV><DIV> </DIV><DIV>Brian <BR><BR>--- <A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A> wrote:<BR><BR>From: hank pronk via Personal_Submersibles <<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>><BR>To: Personal Submersibles General Discussion <<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>><BR>Subject: [PSUBS-MAILIST] penetrator<BR>Date: Fri, 16 Dec 2016 23:01:23 +0000 (UTC)<BR><BR></DIV><DIV><DIV style="color: rgb(0, 0, 0); font-family: HelveticaNeue,Helvetica Neue,Helvetica,Arial,Lucida Grande,sans-serif; font-size: 12px; background-color: rgb(255, 255, 255);"><DIV>Hi All,</DIV><DIV dir="ltr">I am looking for a penetrator supplier, I am hoping to find male ends for some penetrators I have.</DIV><DIV dir="ltr"><BR></DIV><DIV dir="ltr"><BR></DIV><DIV>Hank</DIV></DIV></DIV>_______________________________________________
Personal_Submersibles mailing list
<A>Personal_Submersibles@psubs.org</A>
<A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A>
</DIV></DIV></DIV><BR><DIV>_______________________________________________<BR>Personal_Submersibles mailing list<BR><A href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</A><BR><A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A><BR></DIV><BR><BR></DIV> </DIV> </DIV> </DIV></DIV></DIV></DIV></DIV><BR>_______________________________________________<BR>
Personal_Submersibles mailing list<BR>
<A href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</A><BR>
<A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A><BR>
<BR></BLOCKQUOTE></DIV><BR></DIV>
_______________________________________________
Personal_Submersibles mailing list
<A href="/eonapps/ft/wm/page/compose?send_to=Personal_Submersibles%40psubs.org">Personal_Submersibles@psubs.org</A>
<A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A>
</DIV>