<html><head></head><body><div style="color:#000; background-color:#fff; font-family:HelveticaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif;font-size:16px"><div id="yui_3_16_0_ym18_1_1459515623241_3608"><span>Hi Sean,</span></div><div id="yui_3_16_0_ym18_1_1459515623241_3599" dir="ltr"><span>thanks for the comments.</span></div><div id="yui_3_16_0_ym18_1_1459515623241_3606" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_3607">The system is based on one described in this ex military document called</span></div><div id="yui_3_16_0_ym18_1_1459515623241_3601" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_3600">"Rotary Shaft Seal Selection Handbook For Pressure Equalized Deep Ocean Equipment". <a id="yui_3_16_0_ym18_1_1459515623241_3625" href="http://www.dtic.mil/get-tr-doc/pdf?AD=AD0889330&Location=U2&doc=GetTRDoc.pdf" target="_blank"><font id="yui_3_16_0_ym18_1_1459515623241_3626" color="#196ad4">http://www.dtic.mil/get-tr-doc/pdf?AD=AD0889330&Location=U2&doc=GetTRDoc.pdf</font></a></span></div><div dir="ltr"><span>It is called a double seal redundant arrangement as apposed to the other system</span></div><div id="yui_3_16_0_ym18_1_1459515623241_3676" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_3675">featured which is the double seal cascaded. The double seal cascaded has a pressure</span></div><div id="yui_3_16_0_ym18_1_1459515623241_3678" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_3677">drop from the motor compartment to the seal cavity & again to the water, as you described.</span></div><div id="yui_3_16_0_ym18_1_1459515623241_3777" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_3776">To do the double seal cascaded it would require an additional compensator & I</span></div><div id="yui_3_16_0_ym18_1_1459515623241_3775" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_3781">didn't think it warranted that. </span></div><div id="yui_3_16_0_ym18_1_1459515623241_3780" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_3779">In my redundant system there will be a 4psi above ambient internal pressure generated</span></div><div id="yui_3_16_0_ym18_1_1459515623241_4127" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_4130">by an air regulator. (as Cliff is using)</span></div><div id="yui_3_16_0_ym18_1_1459515623241_4129" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_3818">The external seal sees all the abrasives & anything else external that will degrade it,</span></div><div id="yui_3_16_0_ym18_1_1459515623241_3841" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_3840">& is the first seal to fail. It should fail with oil going out rather than water coming in, but</span></div><div id="yui_3_16_0_ym18_1_1459515623241_3899" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_3898">the document talks about an unpredictable pumping action that the seal can generate</span></div><div id="yui_3_16_0_ym18_1_1459515623241_3901" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_3900">that can overcome the small pressure differential & pump water in. In the event of</span></div><div id="yui_3_16_0_ym18_1_1459515623241_3904" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_3903">water entering the cavity, it should sink (eventually) to the </span><span id="yui_3_16_0_ym18_1_1459515623241_3910">sight tube at the bottom. </span></div><div id="yui_3_16_0_ym18_1_1459515623241_3920" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_3921">The wiring runs up a clear tube as does the compensating oil. I may add an electronic</span></div><div id="yui_3_16_0_ym18_1_1459515623241_3986" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_3985">oil level indicator but initially I will be able to see what's happening.</span></div><div id="yui_3_16_0_ym18_1_1459515623241_3984" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_3983">I have used nitrile lip seals (spring type) because I don't want a lot of pressure on the</span></div><div id="yui_3_16_0_ym18_1_1459515623241_3997" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_4038">shaft & because the thruster is so tiny I didn't want larger face seals taking up space.</span></div><div id="yui_3_16_0_ym18_1_1459515623241_4021" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_4037">Also with the 10mm shaft ( with circlip grooves) I didn't want a long distance from the last bearing to the prop in case the shaft oscillated when running.</span></div><div id="yui_3_16_0_ym18_1_1459515623241_4202" dir="ltr"><span id="yui_3_16_0_ym18_1_1459515623241_4201">I will think a bit more about the cascaded system, & see if there is a cheap simple</span></div><div id="yui_3_16_0_ym18_1_1459515623241_4203" dir="ltr"><span>way of doing it.</span></div><div id="yui_3_16_0_ym18_1_1459515623241_4078" dir="ltr"><span>Cheers Alan </span></div><div id="yui_3_16_0_ym18_1_1459515623241_4036" dir="ltr"><span></span><br></div><div id="yui_3_16_0_ym18_1_1459515623241_3820" dir="ltr"><span></span><br></div><div id="yui_3_16_0_ym18_1_1459515623241_3778" dir="ltr"><span></span><br></div><div class="qtdSeparateBR" id="yui_3_16_0_ym18_1_1459515623241_3609"><br><br></div><div class="yahoo_quoted" id="yui_3_16_0_ym18_1_1459515623241_3683" style="display: block;"> <div id="yui_3_16_0_ym18_1_1459515623241_3682" style="font-family: HelveticaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif; font-size: 16px;"> <div id="yui_3_16_0_ym18_1_1459515623241_3681" style="font-family: HelveticaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif; font-size: 16px;"> <div id="yui_3_16_0_ym18_1_1459515623241_3680" dir="ltr"> <font id="yui_3_16_0_ym18_1_1459515623241_3679" face="Arial" size="2"> <hr size="1"> <b><span style="font-weight: bold;">From:</span></b> Sean T. Stevenson via Personal_Submersibles <personal_submersibles@psubs.org><br> <b><span style="font-weight: bold;">To:</span></b> Personal Submersibles General Discussion <personal_submersibles@psubs.org> <br> <b><span style="font-weight: bold;">Sent:</span></b> Saturday, April 2, 2016 1:25 AM<br> <b><span style="font-weight: bold;">Subject:</span></b> Re: [PSUBS-MAILIST] MK 2 Brushless Thruster<br> </font> </div> <div class="y_msg_container" id="yui_3_16_0_ym18_1_1459515623241_3686"><br><div id="yiv5434474822"><div id="yui_3_16_0_ym18_1_1459515623241_3685"><div id="yui_3_16_0_ym18_1_1459515623241_3684" dir="ltr">Alan, I am unclear as to what purpose the inner seal is serving, given that you have the same fluid at the same pressure on both sides? If you are compensating with positive pressure, an outer seal failure will result in losing some compensating oil to sea, until the pressure is equalized to sea pressure, at which point you may have communication through the outer seal, but no pressure differential to drive fluid transfer. As such, only incidental admission of seawater will occur, but you have a communication channel to your motor compartment bypassing the inner seal, which puts the motor at risk. An inner seal failure alone in your embodiment is entirely inconsequential, and if it is there as a failsafe in case of accidentally developing negative compensation pressure, you defeat that purpose by allowing the intermediate volume to communicate with the motor chamber.</div>
<div id="yui_3_16_0_ym18_1_1459515623241_4079" dir="ltr">When I design mission-critical sealing arrangements, I use the following rule-of-thumb: Use a seal to change fluid, or to change pressure, but not both simultaneously. This ensures that any incidental leakage as a result of dynamic seal movement is usually inconsequential. Accordingly, I might look at your design to see if I could somehow arrange to have the motor compartment at a slight positive pressure for compensation (using either central compensation or a compensation tube or bladder with spring bias to elevate the pressure), and then the inner seal sealing between that oil at slight positive pressure and oil at sea pressure in the isolated intermediate volume so that incidental leakage is oil to oil and inconsequential (using an unbiased compensator for this volume), and then the outer seal sealing that oil at sea pressure against seawater at sea pressure, so no differential exists. If you do that, here is the failure analysis:</div>
<div id="yui_3_16_0_ym18_1_1459515623241_4093" dir="ltr">An inner seal failure will cause oil to move from the motor compartment to the intermediate compartment as a result of the positive pressure. If the displacement of the unbiased compensator on the intermediate chamber is limited, and the displacement of the biased compensator on the motor compartment is large enough to bring the unbiased one on the adjacent chamber to that limit, then you simply end up with the intermediate chamber also being compensated at positive pressure, and the outer seal does a little more work but maintains the arrangement's integrity.</div>
<div id="yui_3_16_0_ym18_1_1459515623241_4094" dir="ltr">Conversely, if you had an outer seal failure, seawater is permitted to communicate with the oil in the intermediate chamber, but there is no pressure differential to drive mixing of the fluids, and in any case, the intermediate chamber remains isolated from the motor compartment which is at slight positive pressure, sealed by the inner seal.</div>
<div id="yui_3_16_0_ym18_1_1459515623241_4095" dir="ltr">Anywhere you employ seals with zero pressure differential across them, they need to be of a spring energized type since the pressure can't do it.</div>
<div id="yui_3_16_0_ym18_1_1459515623241_4096" dir="ltr">Anyway, just a few things to think about.</div>
<div id="yui_3_16_0_ym18_1_1459515623241_4097" dir="ltr">Sean<br clear="none">
</div>
<br clear="none"><br clear="none"><div class="yiv5434474822yqt3288875934" id="yiv5434474822yqtfd26635"><div class="yiv5434474822gmail_quote" id="yui_3_16_0_ym18_1_1459515623241_4098">On April 1, 2016 3:05:09 AM MDT, Alan James via Personal_Submersibles <personal_submersibles@psubs.org> wrote:<blockquote class="yiv5434474822gmail_quote" style="margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex; border-left-color: rgb(204, 204, 204); border-left-width: 1px; border-left-style: solid;">
<div style="color: rgb(0, 0, 0); font-family: HelveticaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif; font-size: 16px; background-color: rgb(255, 255, 255);"><div> Updated version with Hanks suggestion of a channel direct</div><div dir="ltr">to the motor cavity.</div><div dir="ltr">I have also added a bearing at the wiring end of the motor shaft.</div><div id="yiv5434474822yui_3_16_0_ym18_1_1459500900511_2751" dir="ltr">I am not sure about this. It would be easier engineering wise, to locate the motor in</div><div id="yiv5434474822yui_3_16_0_ym18_1_1459500900511_2752" dir="ltr">a central back bearing & have the holes for the locating pins a bit over sized,</div><div id="yiv5434474822yui_3_16_0_ym18_1_1459500900511_2795" dir="ltr">rather than a tight fit. That way they would only serve to stop the rotation of the </div><div id="yiv5434474822yui_3_16_0_ym18_1_1459500900511_2792" dir="ltr">back section of the motor. According to my propeller calculator, adding another</div><div id="yiv5434474822yui_3_16_0_ym18_1_1459500900511_2794" dir="ltr">sh!
aft
bearing will reduce the power output by 1.5%.</div><div id="yiv5434474822yui_3_16_0_ym18_1_1459500900511_2793" dir="ltr">Alan</div><div id="yiv5434474822yui_3_16_0_ym18_1_1459500900511_2753" dir="ltr"><br clear="none"></div></div><div style="margin-top: 2.5em; margin-bottom: 1em; border-bottom-color: rgb(0, 0, 0); border-bottom-width: 1px; border-bottom-style: solid;"></div><pre class="yiv5434474822k9mail"></pre><hr><br clear="none">Personal_Submersibles mailing list<br clear="none">Personal_Submersibles@psubs.org<br clear="none"><a href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles" target="_blank" rel="nofollow" shape="rect">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</a><br clear="none"></blockquote></div></div></div></div><br><div class="yqt3288875934" id="yqtfd74426">_______________________________________________<br clear="none">Personal_Submersibles mailing list<br clear="none"><a href="mailto:Personal_Submersibles@psubs.org" shape="rect" ymailto="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</a><br clear="none"><a href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles" target="_blank" shape="rect">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</a><br clear="none"></div><br><br></div> </div> </div> </div></div></body></html>