<div dir="ltr">I have, and so far so good with a caveat. I have two lights. They both still work well after a year, and have been to 250 feet. That said, one of them replaced a little of the oil with fresh water on the last outing. I think the problem was where the cable enters the housing, because it got severely pulled sideways (light snagged in tow line). These are really well made, but even better would be a light like you say with a part can be pulled for drilling and tapping. Hank, do you think there's enough space to install a proper electrical penetrator? I would love to get rid of the weak spot factory cable seal.<div><br></div><div>Thanks,<br><br>Alec</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Sun, Jun 21, 2015 at 9:40 PM, hank pronk via Personal_Submersibles <span dir="ltr"><<a href="mailto:personal_submersibles@psubs.org" target="_blank">personal_submersibles@psubs.org</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><br>
Alan,<br>
Hmmm maybe I should remove the electronics and put them inside the sub. I thought Alec was doing the same thing, just flooding the whole light.<br>
Hank--------------------------------------------<br>
<span class="">On Sun, 6/21/15, Alan James via Personal_Submersibles <<a href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</a>> wrote:<br>
<br>
Subject: Re: [PSUBS-MAILIST] LED light bar<br>
To: "Personal Submersibles General Discussion" <<a href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</a>><br>
</span> Received: Sunday, June 21, 2015, 9:31 PM<br>
<br>
Hank,the led<br>
<span class=""> electronics I've looked at in some of my<br>
lampshave<br>
electrolytic capacitors in them, which can crush under<br>
pressure.So<br>
"if" it fails at depth this may be a heads up as<br>
to why.Alan<br>
<br>
<br>
</span><span class=""> From: hank pronk via<br>
Personal_Submersibles<br>
<<a href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</a>><br>
<br>
To:<br>
<a href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</a><br>
Sent: Monday, June 22,<br>
2015 12:09 PM<br>
Subject:<br>
[PSUBS-MAILIST] LED light bar<br>
<br>
<br>
Success, my new light bar is installed and full<br>
of oil. It was remarkably easy, the end caps come off the<br>
bar and are quite heavy, so tapping a 1/8 pipe thread was<br>
easy. I filled the light while the end cap was off then<br>
reassembled it and topped it up through the hose fitting. <br>
I have a p trap line (1/8 nylon) and the whole conversion<br>
takes less than an hr. The light works just fine, maybe<br>
not as bright as my halogen lights but much easier on<br>
power. The light runs on 10 amps at 24V. 24,000 lumen<br>
Hank<br>
_______________________________________________<br>
Personal_Submersibles mailing list<br>
<a href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</a><br>
<a href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles" rel="noreferrer" target="_blank">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</a><br>
<br>
<br>
<br>
<br>
</span> -----Inline Attachment Follows-----<br>
<div class="HOEnZb"><div class="h5"><br>
_______________________________________________<br>
Personal_Submersibles mailing list<br>
<a href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</a><br>
<a href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles" rel="noreferrer" target="_blank">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</a><br>
<br>
<br>
_______________________________________________<br>
Personal_Submersibles mailing list<br>
<a href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</a><br>
<a href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles" rel="noreferrer" target="_blank">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</a><br>
</div></div></blockquote></div><br></div>