[PSUBS-MAILIST] K-600

[cast55 at telus.net]

External rings will always give you a stronger hull compared to internal for the same hull thickness and ring spacing. The downside is that the welds have to be perfect, but any weld shrinkage that may occur actually acts to deform the hull in a way that increases its strength over that of the nominal geometry.

Sean


vbra676539 at aol.com wrote:
>
>PC-8 has 3/8" wall thickness on the hull cylinder, the same as the 600,
>but was rated 200 feet deeper by ABS, even though it has a larger
>radius (21" as opposed to 18"). The ring stiffeners on the 8 are
>external and the conning tower larger. Makes you wonder what the deal
>is for figuring operating depth. Perry went to half inch for PS-2 which
>was the same boat but rated at 1000'. Hmmm.
>Vance
>
>
>-----Original Message-----
>From: greg cottrell <jgcottrell2002 at yahoo.com>
>To: Personal Submersibles General Discussion
><personal_submersibles at psubs.org>
>Sent: Thu, Oct 24, 2013 10:24 am
>Subject: Re: [PSUBS-MAILIST] K-600
>
>
>
>I thought that George said they were .625" but I could be wrong.
> 
>
>
>
>
>From: Jon Wallace <jon.wallace at yahoo.com>
>To: Personal Submersibles General Discussion
><personal_submersibles at psubs.org> 
>Sent: Thursday, October 24, 2013 10:14 AM
>Subject: Re: [PSUBS-MAILIST] K-600
>
>
>It was an engineer hired by the company that commissioned and purchased
>the 600.  His calculation requirements for the heads came out a little
>bit thicker than what George had calculated.  I believe George spec'd
>.5 inch and the company's engineer spec'd .5625 inch.
>
>--------------------------------------------
>On Thu, 10/24/13, greg cottrell <jgcottrell2002 at yahoo.com> wrote:
>
>Subject: Re: [PSUBS-MAILIST] K-600
>To: "Personal Submersibles General Discussion"
><personal_submersibles at psubs.org>
>Date: Thursday, October 24, 2013, 9:25 AM
>
>George attributed the miscalculation in the weight
>of the 600 to second guessing the thickness of the heads.
>His original design called for thinner heads but
>someone (can't remember who) that George respected
>suggested that they should be thicker. George used the
>thicker heads and then found that the sub wouldn't
>float. He had the hull lengthened by Bath Iron Works to get
>the needed buoyancy back. He
>said he was amazed at how fast they turned the job around- I
>think it was only a few days.
> 
>Greg
> 
>
>
>
>_______________________________________________
>Personal_Submersibles mailing list
>Personal_Submersibles at psubs.org
>http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
>
>
>
>
>
>_______________________________________________
>Personal_Submersibles mailing list
>Personal_Submersibles at psubs.org
>http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
> 
>
>
>------------------------------------------------------------------------
>
>_______________________________________________
>Personal_Submersibles mailing list
>Personal_Submersibles at psubs.org
>http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

-- 
Sent from Kaiten Mail. Please excuse my brevity.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20131024/239e32a0/attachment-0001.html>