[PSUBS-MAILIST] Windows

More than one cable in a blue globe will not work. 
The cabel outside needs to be round and minimum 5 mm outside up to 11 mm diameter. 
But can be a multiple wire cabel as long as the outside is a cylinder shape. 

vbr Carsten 

"hank pronk" <hanker_20032000 at yahoo.ca> schrieb: 
Thanks; guys.
I was under the impression there was no potting needed.  I was thinking of making something from compression fittings with a very tightly packed wire group in a relatively hard shell.   
Hank



On Thursday, December 19, 2013 3:35:01 AM, James Frankland <jamesf at guernseysubmarine.com> wrote:

Blue Globe seem to make all sorts of cable glands, including ones for multi cables.  I did try and get some but the local supplier in the UK wasnt interested once i said i only wanted a few.  The catalogues are huge, but i think there are some multi glands in the one called, "novelties".  !

http://www.pflitsch.de/en/cable-glands-downloads/cat_view/46-kabelverschraubung/51-kataloge/120-gesamtkatalog-kabelverschraubungen--kapitel


On 18 December 2013 19:11, Alan <alanlindsayjames at yahoo.com> wrote:

Hi Hank,
I don't know what the "rules are on them yet"
I think their pressure rating is well below what they have 
been tested to by Emile (3000ft).
The European Psubbers use 2 per penetration, 1 either side of the hull.
It would depend on the configuration of the multi strand wire as to how
it sealed up. Experiment or test? 
I put two wires through the same penetration by buying an item that
fitted in to the Blue Globe Gland & potting the wires in this.
It was basically a pipe with an outside lip to stop it extruding in through
the BGCG & an inner narrowing at one end to stop the potting from
extruding through.
In hind-site an elbow may have been good to pot in to.
Regards Alan 

Sent from my iPad

On 19/12/2013, at 4:30 AM, hank pronk <hanker_20032000 at yahoo.ca> wrote:


Does anyone know what the rules are concerning electrical penetrators.  I understand some people use Blue Globe compression fittings.  Can a multi wire cord be used with a Blue Globe fitting?
Hank



On Sunday, December 15, 2013 2:26:09 PM, hank pronk <hanker_20032000 at yahoo.ca> wrote:

Jon,
Agreed, I am concerned of coarse about the buffing temperature.  In my case the ports are in quite good condition, and should need minimal buffing.  The mbt windows are in rough shape but they are not under stress like a port so we can get tough with them.  
Hank



On Sunday, December 15, 2013 2:17:09 PM, Jon Wallace <jonw at psubs.org> wrote:


It looks like GL has similar wording, depending upon actual usage and detailed testing agreed to by GL a service life extension may be granted.  For the person desiring a certified vessel I agree new windows would probably be a cheaper route unless you were very sure the existing windows would pass the required testing.  Scratches are a no-no however so you really need to get them completely buffed out.  The heat produced in buffing may justify annealing however if the windows were manufactured to PVHO standards there's a lot of safety factor built in.



On 12/15/2013 4:01 PM, hank pronk wrote:

Jon,
Yes, that is what I call the bible.  I just read on page 940 that ABS accepts the extrapolation method to determine remaining service life. The test is very extensive and for a flat disk window  it would probably be cheaper to buy new windows.  I did not see that re- annealing helps.
Hank






_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles







_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles


_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles






_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles




 

-- 

Carsten Standfuß
Dipl.Ing.Schiffbau @ Meerestechnik
Heinrich Reck Str.12A
18211 Admannshagen Germany

+49 (0) 172 8464 420
WWW.Euronaut.org
Carsten at euronaut.org
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20131219/0c3c9f22/attachment-0001.html>