[PSUBS-MAILIST] G.L. summary Pressure Hull

[vbra676539 at aol.com]

Beautiful job, Hank. It looks great. And the motor is shiny!
Vance



-----Original Message-----
From: hank pronk <hanker_20032000 at yahoo.ca>
To: Personal Submersibles General Discussion <personal_submersibles at psubs.org>
Sent: Thu, Dec 12, 2013 1:28 pm
Subject: Re: [PSUBS-MAILIST] G.L. summary Pressure Hull



Vance,
I posted a picture of my new motor and seal assembly, (Gamma Restoration)  you can see I put  bearings and seals in the tail cone. You can't see it but I also have two ss lines that feed water to the shaft tube from outside the mbt.  This ensures the tube fills before I run the motor and also drains to prevent freezing.
Hank
 
 
 
 
 
  On Thursday, December 12, 2013 10:31:05 AM, hank pronk <hanker_20032000 at yahoo.ca> wrote:
  
  


Dan,
Thank you, I will play around with it.  I guess that's how we learn.
Hank
 
 
 
 
 
  On Thursday, December 12, 2013 9:48:21 AM, Dan H. <jumachine at comcast.net> wrote:
  
  

If you don't have a taper attachment, use the compound slide on the lathe.  It's tricky to set since your working on fractions of a degree for a good fit but you fine tune it with a few trial pieces.  
 
Dan H.
  
----- Original Message ----- 
  
From:   hank   pronk 
  
To: Personal Submersibles General   Discussion 
  
Sent: Thursday, December 12, 2013 10:16   AM
  
Subject: Re: [PSUBS-MAILIST] G.L. summary   Pressure Hull
  


  
  
Does anyone have a trick to machining an inside taper without lathe    attachments.  I need to make a hub to fit a tapered   shaft.  I made one by trial and error and it will work but it is not   perfect. 
  
Hank 
  


  
  
  
On Thursday, December 12, 2013 7:13:39   AM, Jon Wallace <jonw at psubs.org>   wrote:

  
  
  
  

I should have stated up   front that we were just having some fun and I hope nobody concentrating on   ROV/AUV development and operation takes offense.  PSUBS welcomes ROV and   AUV discussions here as well.

Jon

  

On 12/11/2013 9:57 PM, Alan James wrote:

  
  
    
    
Thanks Keith,
    
hope     didn't see the phone sex & ROV comments
    
earlier 
    
Keith     owns a ROV company.
    
Alan






  
_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles






  
  

  _______________________________________________
Personal_Submersibles   mailing   list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles




_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles




  
 
  
 




  
 
  
 


_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20131212/2acef933/attachment-0001.html>